QUESTION 171 To create a new Ethernet VLAN, you need to perform (Choose all that apply)?
A. set vlan vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
B. set vlanID vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
C. Go into interface mode
D. set vlanint vlan_num [name name] [said said] [mtu mtu] [translation vlan_num]
E. Go into privileged mode Answer: A, E Explanation: Not E: The question is referring to catos and you as dont need to go into privileged mode.
QUESTION 172 You are considering to set up multiplayer switching. Commands that will be used to configure an internal or external Multi-layer Switch Route Processor include: mls rp vlan-id What is this command for?
A. for enabling MLSP
B. for assigning VLAN ID to route processor interface
C. for enabling the RSM interface
D. for placing an external route processor in the interface of the VTP domain switch
E. for entering into the router interface Answer: B
QUESTION 173 You are a Cisco Certified Engineer. You are configuring a switching solution. You want to take advantage of the Fast EtherChannel ports. Which of the following guidelines can help you avoid configuration problems that may cause a port to be automatically disabled (Choose all that apply)?
A. Allow some ports in a channel to be partly disabled.
B. Configure ALL the ports in a channel as dynamic.
C. Assign all ports in a channel to the same VLAN
D. Allow some ports in a channel to be disabled.
E. Allow all ports in a channel to be disabled.
F. Configure all ports in a channel to operate at the same speed but in different duplex modes. Answer: C Explanation:
According to Cisco: Cisco's Fast EtherChannel technology builds upon standards based 802.3 full duplex Fast Ethernet to provide network managers a reliable high speed solution for the campus network backbone. Fast EtherChannel provides bandwidth scalability within the campus by providing increments from 200 Mbps to 800 Mbps with multi-gigabit capacity in the future. Fast EtherChannel technology not only solves the immediate problem of scaling bandwidth within the network backbone today, but also paves the path for an evolution to standards-based Gigabit Ethernet and beyond, because Fast EtherChannel technology can be applied to support Gigabit EtherChannel. More information can be found at: this site
QUESTION 174 When configuring VTP, you want to set the management domain name. What command will you use?
A. set vtp domain
B. show vtp
C. set vtp
D. set vtp pruneeligible Answer: A
QUESTION 175 Which of the following are reasons to deploy Dynamic Trunking Protocol (Choose all that apply)?
A. for supporting auto-negotiation of IEEE 802.1QUESTION NO: trunks
B. for supporting auto-negotiation of ISL
C. for managing trunk negotiation in 2500 router supervisor engine software R 4.2 or later
D. for managing trunk negotiation in Catalyst supervisor engine software R 4.2 or later. Answer: A, B, D
QUESTION 176 When configuring VTP, you want to allow pruning to take effect. What command will you use?
A. show vtp
B. set vtp
C. set vtp domain
D. set vtp pruneeligible Answer: D
QUESTION 177 You are a Cisco Certified Engineer. You are configuring a switching solution. You have configured a catalyst switch to operate in a VTP mode. Your switch can no longer advertise its VLAN configuration. Which VTP modes are NOT currently effective (Choose all that apply)?
A. Client
B. Server
C. Host
D. Transparent
E. Native Answer: A, B, C, E Explanation: According to Cisco: You can configure a switch to operate in any one of these VTP modes: Server-In VTP server mode, you can create, modify, and delete VLANs and specify other configuration parameters (such as VTP version and VTP pruning) for the entire VTP domain. VTP servers advertise their VLAN configuration to other switches in the same VTP domain and synchronize their VLAN configuration with other switches based on advertisements received over trunk Links. VTP server is the default mode. Client-VTP clients behave the same way as VTP servers, but you cannot create, change, or delete VLANs on a VTP client. Transparent-VTP transparent switches do not participate in VTP. A VTP transparent switch does not advertise its VLAN configuration and does not synchronize its VLAN configuration based on received advertisements. However, in VTP version 2, transparent switches do forward VTP advertisements that they receive out their trunk ports.
QUESTION 178 You are a Cisco Certified Engineer. You are configuring a switching solution. What command do you use to display only the blocked ports in your spanning tree environment (fill in the blank): Answer: show spantree blockedports Explanation: According to Cisco: Use the show spantree blockedports command to display only the blocked ports. show spantree blockedports [vlan_num]vlan_num (Optional) Number of the VLAN.
QUESTION 179 You are a Cisco Certified Engineer. You are configuring a switching solution. An Ethernet media trunk link is to be configured between two Cisco switches. These switches have identical modules, software revisions and VLAN configuration information. Which of the following are NOT required for the trunk to operate (Choose all that apply)?
A. The link must be point to point for ISL.
B. The link must be 100Mbs or slower
C. The link must use IEEE 802.1QUESTION NO: trunk protocol.
D. The link may use IEEE802.1QUESTION NO: trunk protocol when the SAID parameter is correctly set. Answer: A, B Explanation: According to Cisco: VLAN Trunk Protocol (VTP) reduces administration in switched network. When you configure a new VLAN on one VTP server, the VLAN is distributed through all switches in the domain. This reduces the need of configuring the same VLAN everywhere. VTP is a Cisco-proprietary protocol that is available on most of the Cisco Catalyst Family products. More configuration information can be found at: this site
QUESTION 180 What is the VLAN default value for TrCRF bridge mode?
A. IBM
B. SRB
